Huntersigma416

Congratulations on your purchase and welcome to the growing number of cyclists who are discovering a powerful new generation of bicycle computers. Your Specialized SpeedZone® Team has been designed to provide the best combination of performance, features, durability and ease of use and installation.

• Specialized Speedzone Sport Manual
• Specialized Sport Computer Instruction Manual
• Speedzone Sport Wireless Operating Manual
• Specialized Bike Odometer Instructions
• Speedzone Sport Wireless Computer Manual
• Specialized Sport Bike Computer User Manual Youtube

The following functions available on your

SpeedZone® Team bicycle computer:

Specialized cylcocomputer user manual (11 pages) Summary of Contents for Specialized SpeedZone Page 1 Cycle Computer, please read all sections carefully and reference it when preforming the initial programming and operation of the unit. (Specialized P/N 4812-3100) from your Specialized dealer. To install the 31.8mm diameter strap onto your SpeedZone Pro, remove the two Philips head screws from the bottom of the computer and push out the retaining pin with a small screwdriver or a straightened paperclip.

What is included in you SpeedZone® Team package:

1.SpeedZone® Team Computer (1)

2.Mounting bracket (2)

3.Magnet with screw (1)

4.Cable tie wraps (4)

5.Mounting bracket sizing straps (3)

6.Transmitter (1)

7.Transmitter mounting bracket (1)

Mounting the SpeedZone® Team:

The SpeedZone® Team Wireless transmitter can mount on the right or the left side of the fork blade. The right side should be used on large frames or when a suspension fork is installed. The optimal distance between the computer and the transmitter is 24 inches (610mm) The distance may need to be less that 24 inches (610mm) if ambient temperatures are below 40 °F (4 °C). To reduce signal loss in colder temperatures, the transmitter should be mounted as close to the computer as possible. (maximum mounting distance is 28 inches). Use the transmitter mounting bracket and tie-wraps provided to position the sensor. Do not tighten the tie-wraps until final placement

fig.1 fig.2

of the magnet is correct. See figure 1. Attach the magnet to a spoke across from the transmitter with the magnet screw. The clearance between the magnet and the transmitter should be approximately 1/32”- 1/16” (1-2mm). Tighten the magnet and transmitter. Do not over-tighten the magnet screw See figure 2.

Attach the mount to the handlebar using the bracket screw provided. Tighten so that the bracket cannot rotate on the handlebar.

There are several sizing straps provided to fit different diameter bars See figure 3.

fig.3

tor will flash. If it does not flash, check the sensor and magnet alignment. Realign as necessary until the “wheel option” indicator flashes while spinning the wheel.

3

Programming:

Programming the functions of your SpeedZone® Team requires it to be placed in various “modes” (i.e. odometer mode, distance mode). The computer can be cycled through these modes by pressing the “MODE” button located on the right-hand side of the housing. Once a specific mode has been entered, its values can be reset or adjusted by pressing either the “FUNCTION” button located on the left hand side of the housing or by using a combination of the “MODE” and “FUNCTION” buttons.

1. Miles or Kilometers selection:

Your SpeedZone® Team will record speed and distance in either miles (M/h) or kilometers (KM/h). To enter your selection of miles or kilometers, push the “MODE” button until ODO (odometer) appears in the lower left side of the display (This is called the odometer mode). Hold down the “FUNCTION” (left side) button and ‘tap’ the “MODE” button once. The Km/h, m/h indicator will begin blinking. You may now

4

alternate between miles and kilometers by pressing the “MODE” button. When the correct choice is flashing, select it by pressing the “FUNCTION” button. You will now enter the “Programmable Odometer” mode. If the odometer setting is correct push the “FUNCTION” button (5 times) to exit to odometer mode (otherwise, see “Setting the programmable odometer below).

2. Setting the

Programmable Odometer:

The programmable odometer mode is accessed by enter-

ing the odometer (ODO) mode and holding down the “FUNCTION” button and ‘tapping’ the “MODE” button once. The Km/h indicator will flash. If the Km/h setting is correct press the “FUNCTION” button once and a five digit number will appear. You are now in the programmable odometer mode. This mode is useful if you have replaced the battery and would like to

retain the mileage you have already ridden. To enter a mileage into the odometer, press the “MODE” button until the flashing digit is correct. (Note: The “MODE” button may be held to scroll to the correct digit.) Press the “FUNCTION” button to select the next digit to the right. Repeat the process until all five digits are entered as your existing mileage.

Specialized Speedzone Sport Manual

3. Wheel Circumference Selection:

To set the circumference for the type of tires you are using, you can use Specialized’s exclusive “Easy Calibration Mode” or measure your actual tire circumference by the roll-out method. Two different tire diameters may be entered into the computer’s “Second Wheel Option.”

Specialized Sport Computer Instruction Manual

Easy Calibration Mode:

Your SpeedZone® Team has been preprogrammed with the following 14 Specialized tire sizes:

When using Easy Calibration Mode, the

Speedzone Sport Wireless Operating Manual

Specialized Bike Odometer Instructions

“FUNCTION” button for three seconds. The display will now show the currently selected tire size for wheel option #1.

Speedzone Sport Wireless Computer Manual

To scroll through the preprogrammed tire sizes tap both the “MODE” and “FUNCTION” buttons simultaneously. When you reach the desired tire size press the “FUNCTION” button once to select it and enter Easy Calibration Mode for wheel option #2. Follow the same procedure to program the wheel #2 tire size and tap the

Specialized Sport Bike Computer User Manual Youtube